Bearing 33108A SNR

Tapered roller bearings 33108A

Bearing number : 33108A

Size mm : 40x75x26

Brand : SNR

Bore Diameter mm : 40

Outer Diameter mm : 75

Width mm : 26

Bearing dimensions and specification in brand catalogue :

d - 40 mm

D - 75 mm

T - 26 mm

B - 26 mm

C - 20,5 mm

Weight - 0,52 Kg

Bearing 33108A SNR Shielded bearings have a storage life of five years and a further two years operational life following installation. Wash all bearing parts with a noncontaminating solvent. Lightly pack the bearings with grease applying a 33% fill by volume into the bearing and housings. Where Bearing 33108A SNR space heaters are fitted, and the storage environment has wide humi dity and temperature variations, it is strongly recommended they be energised. Warnings should be placed on the Bearing 33108A SNR to make operatives aware of the live heaters Supplies are normally 220-240 volt single phase, from a 380-415 volt three phase supply. See terminal box lid for details.

Bearing 33108A SNR Shielded bearings have a storage life of five years and a further two years operational life following installation. Wash all bearing parts with a noncontaminating solvent. Lightly pack the bearings with grease applying a 33% fill by volume into the bearing and housings. Where Bearing 33108A SNR space heaters are fitted, and the storage environment has wide humi dity and temperature variations, it is strongly recommended they be energised. Warnings should be placed on the Bearing 33108A SNR to make operatives aware of the live heaters Supplies are normally 220-240 volt single phase, from a 380-415 volt three phase supply. See terminal box lid for details.

Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33108A SNR. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33108A SNR brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33108A SNR.

Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33108A SNR. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33108A SNR brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33108A SNR.

Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33108A SNR. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33108A SNR brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33108A SNR.

Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33108A SNR. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33108A SNR brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33108A SNR.