Maison>Produits>Tapered Roller Bearings>Bearing 33030 Timken
Bearing 33030 Timken 33030 Timken MODELS
Need a CAD or 3D Model?
Bearing 33030 Timken
Tapered Roller Bearings
Bearing 33030 Timken 33030 Timken Bearing SPECIFICATIONS
- Bearing 33030 Timken
33030 Timken
-
Crystal2020-07-10 09:46:19
Welcome to my shop! Glad to serve you! Please send your question!
Bearing 33030 Timken 33030 Timken Description du produit

Tapered roller bearings 33030
Bearing number : 33030
Size mm : 150x225x59
Brand : Timken
Bore Diameter mm : 150
Outer Diameter mm : 225
Width mm : 59
Bearing dimensions and specification in brand catalogue :
d - 150 mm
D - 225 mm
T - 59 mm
B - 59 mm
C - 46 mm
R - 3 mm
r - 2,5 mm
Weight - 8 Kg
Dynamic load rating radial C - 530 kN
Calculation factor e - 0,36
Calculation factor Y - 1,65
Catalogue,Brandslist,,Bearing 33030 Timken
Bearing 33030 Timken Shielded bearings have a storage life of five years and a further two years operational life following installation. Wash all bearing parts with a noncontaminating solvent. Lightly pack the bearings with grease applying a 33% fill by volume into the bearing and housings. Where Bearing 33030 Timken space heaters are fitted, and the storage environment has wide humi dity and temperature variations, it is strongly recommended they be energised. Warnings should be placed on the Bearing 33030 Timken to make operatives aware of the live heaters Supplies are normally 220-240 volt single phase, from a 380-415 volt three phase supply. See terminal box lid for details.
Bearing 33030 Timken Shielded bearings have a storage life of five years and a further two years operational life following installation. Wash all bearing parts with a noncontaminating solvent. Lightly pack the bearings with grease applying a 33% fill by volume into the bearing and housings. Where Bearing 33030 Timken space heaters are fitted, and the storage environment has wide humi dity and temperature variations, it is strongly recommended they be energised. Warnings should be placed on the Bearing 33030 Timken to make operatives aware of the live heaters Supplies are normally 220-240 volt single phase, from a 380-415 volt three phase supply. See terminal box lid for details.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33030 Timken. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33030 Timken brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33030 Timken.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33030 Timken. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33030 Timken brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33030 Timken.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33030 Timken. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33030 Timken brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33030 Timken.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 33030 Timken. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 33030 Timken brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 33030 Timken.
Bearing 33030 Timken 33030 Timken INTERCHANGE
Tapered Roller Bearings Part series 33030 Timken is a potential replacement for these common bearing part numbers:
33030 Timken
33030 Timken
33030 Timken
33030 Timken
33030 Timken
33030 Timken
33030 Timken
33030 Timken
Contactez-nous

- Adresse
- téléphone professionnel(Temps de travail)
- Fax
Bearing 33030 Timken 33030 Timken Technical Articles
La gestion et l'entretien de la pompe à engrenages à haute température |
Commune de failles et de solutions de pompe à boue |
La cause technique de l’apurement de diamètre de bague et arbre pompe à vis |
Tapered Roller Bearings CATEGORIES
- Tapered Roller Bearings
- parker PV piston pump
- CONTROLLER
- FURNAN PUMP
- Plain Bearing
- Cylindrical Roller Bearings
- PRECISION BALL BEARINGS
- Vickers vane pump
- Bearing catalog
- VICKERS Piston pump
- PRECISION BALL BEARINGS
- Tapered Roller Bearings
- Needle Roller Bearing
- CRUSHER
- POWER TRAIN ASS
- YUKEN vane pump
- TRACK FRAME
- Cylindrical Roller Bearing
- bearing online
- Self-Aligning Ball Bearings
- NACHI piston pump
- REVOLVING FRAME
Customers Who Viewed Bearing 33030 Timken 33030 Timken Bearing Also Viewed
- Mots clés:
Timken
150x225x59