Maison>Produits>Tapered Roller Bearings>Bearing 47890/47820 ISO
Bearing 47890/47820 ISO 47890/47820 ISO MODELS
Need a CAD or 3D Model?
Bearing 47890/47820 ISO
Tapered Roller Bearings
Bearing 47890/47820 ISO 47890/47820 ISO Bearing SPECIFICATIONS
- Bearing 47890/47820 ISO
47890/47820 ISO
- Crystal2020-07-10 09:46:19
Welcome to my shop! Glad to serve you! Please send your question!
Bearing 47890/47820 ISO 47890/47820 ISO Description du produit
Tapered roller bearings 47890/47820
Bearing number : 47890/47820
Size mm : 92.075x146.05x33.338
Bore Diameter mm : 92,075
Outer Diameter mm : 146,05
Width mm : 33,338
Bearing dimensions and specification in brand catalogue :
d - 92,075 mm
D - 146,05 mm
T - 33,338 mm
B - 34,925 mm
C - 26,195 mm
a - 1 mm
Weight - 2,03 Kg
Catalogue,Brandslist,,Bearing 47890/47820 ISO
Bearing 47890/47820 ISO Shielded bearings have a storage life of five years and a further two years operational life following installation. Wash all bearing parts with a noncontaminating solvent. Lightly pack the bearings with grease applying a 33% fill by volume into the bearing and housings. Where Bearing 47890/47820 ISO space heaters are fitted, and the storage environment has wide humi dity and temperature variations, it is strongly recommended they be energised. Warnings should be placed on the Bearing 47890/47820 ISO to make operatives aware of the live heaters Supplies are normally 220-240 volt single phase, from a 380-415 volt three phase supply. See terminal box lid for details.
Bearing 47890/47820 ISO Shielded bearings have a storage life of five years and a further two years operational life following installation. Wash all bearing parts with a noncontaminating solvent. Lightly pack the bearings with grease applying a 33% fill by volume into the bearing and housings. Where Bearing 47890/47820 ISO space heaters are fitted, and the storage environment has wide humi dity and temperature variations, it is strongly recommended they be energised. Warnings should be placed on the Bearing 47890/47820 ISO to make operatives aware of the live heaters Supplies are normally 220-240 volt single phase, from a 380-415 volt three phase supply. See terminal box lid for details.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 47890/47820 ISO. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 47890/47820 ISO brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 47890/47820 ISO.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 47890/47820 ISO. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 47890/47820 ISO brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 47890/47820 ISO.
Insulation resistance During extended storage a three monthly insulation test is recommended to avoid possible lengthy drying out periods when installing Bearing 47890/47820 ISO. Use a 500 volt d.c. Megger.The insulation resistance between phases and between the windings and the frame should be checked. The insulation resistance should be maintained above 10 megohm. If a lower reading is measured, use one of the drying out methods recommended on page 14 until an acceptable reading is obtained. If heaters are fitted but not energised, they should be used in future. Wound rotors Ideally, wound Bearing 47890/47820 ISO brushes should not be in contact with the slip-rings during storage as there is a risk of corrosion. Brushes should either be lifted off the slip-rings or stored separately. This may not be possible with small Bearing 47890/47820 ISO.
Bearing 47890/47820 ISO 47890/47820 ISO INTERCHANGE
Tapered Roller Bearings Part series 47890/47820 ISO is a potential replacement for these common bearing part numbers:
47890/47820 ISO
47890/47820 ISO
47890/47820 ISO
47890/47820 ISO
47890/47820 ISO
47890/47820 ISO
47890/47820 ISO
47890/47820 ISO
Contactez-nous
- Adresse
- téléphone professionnel(Temps de travail)
- Fax
Bearing 47890/47820 ISO 47890/47820 ISO Technical Articles
La gestion et l'entretien de la pompe à engrenages à haute température |
Commune de failles et de solutions de pompe à boue |
La cause technique de l’apurement de diamètre de bague et arbre pompe à vis |
Tapered Roller Bearings CATEGORIES
- Tapered Roller Bearings
- parker PV piston pump
- CONTROLLER
- FURNAN PUMP
- Plain Bearing
- Cylindrical Roller Bearings
- PRECISION BALL BEARINGS
- Vickers vane pump
- Bearing catalog
- VICKERS Piston pump
- PRECISION BALL BEARINGS
- Tapered Roller Bearings
- Needle Roller Bearing
- CRUSHER
- POWER TRAIN ASS
- YUKEN vane pump
- TRACK FRAME
- Cylindrical Roller Bearing
- bearing online
- Self-Aligning Ball Bearings
- NACHI piston pump
- REVOLVING FRAME
Customers Who Viewed Bearing 47890/47820 ISO 47890/47820 ISO Bearing Also Viewed
- Mots clés:
ISO
92.075x146.05x33.338